This guide is divided into two parts: 1. Troubleshooting Connection Issues; 2. Connection Methods for DWARF II

1. Troubleshooting Connection Issues

1.1 DWARF II Loses Connection Suddenly

If your DWARF II disconnects unexpectedly, follow these steps:

Check the SD Card: Ensure there is sufficient space. If the SD card is full, reformat or clear it and try again.
Check the Battery Level: Charge DWARF II if the battery is low.
Check the Distance: Ensure DWARF II is within 5 meters of your device.
Upload a Log:
- Go to Settings > Support > Log Upload in the DWARFLAB app.
- Fill in the required information and ensure your phone/tablet is connected to WiFi or cellular data before submitting.
- Contact our support team at support@dwarflab.com after uploading the log.
For Android Users:
- Disable "Stay Connected" or similar features in your phone’s WiFi settings to prevent it from switching networks.
- If prompted, select "No thanks" when asked to switch to another network.

1.2 "Device Not Found" in the DWARFLAB App

If the app shows "Device Not Found" and there is no green bar for DWARF II:

Reboot DWARF II and your device, then retry.
If the issue persists, contact our support team for remote assistance. Let us know your laptop’s operating system (Windows or macOS) so we can provide further instructions.

1.3 Green Bar Appears but Connection Fails

If you see the green bar in the DWARFLAB app but still cannot connect:

Check your phone’s WiFi list for DWARF II’s network name.
- If DWARF’s WiFi is missing: Contact our support team for assistance.
- If DWARF’s WiFi is visible: Connect using the password DWARF_12345678.
If DWARF II still doesn’t function properly, send us a screenshot of Settings > Connection Settings for further help.

1.4 Bluetooth or Connection Errors

If you encounter errors such as "Bluetooth Communication Error" or "Connection Failed" (error codes 1000–1006):

Reboot both your phone and DWARF II, then retry.
Check your phone’s WiFi list for DWARF II’s network and attempt to connect manually.

1.5 Incorrect Password

If you see an "Incorrect Password" error:

Use the "Forget Password" option in your phone’s WiFi settings.
Reset DWARF II’s Bluetooth and WiFi password, then retry.

1.6 iPhone-Specific Issue: "Unable to Join the Network DWARF_XXX"

If this prompt appears on an iPhone:

Go to Settings > General > Transfer or Reset iPhone > Reset Network Settings.
Retry the connection after resetting the network.

1.7 STA Mode Connection Problems

If you encounter errors like "STA Connection Failed, Error -9" or similar codes in STA mode:

Ensure DWARF II is within the networkWiFi range and the correct password is entered.
If DWARF II is out of WiFi range, disable STA mode and connect directly.
If using another hotspot, go to Settings > Connection Settings > STA Mode to repeat the connection process.

Additional Tips for STA Mode:

Use a 5GHz WiFi network for better performance (2.4GHz may cause lag).
Follow these steps if the connection still fails:
1. Turn off WiFi Compatible Mode, Activate WiFi at Startup, and Enable 2.4G in Settings > Connection Settings, then retry.
2. Clear the cache for both your phone and the DWARFLAB app.
3. Ensure the WiFi name and password are correct, and the signal is strong.
4. Verify that your router supports "Station Mode" and no other devices are using the same IP address.
5. Check if DWARF II’s MAC address is blocked in your router’s filter. If it is, remove it from the filter.
6. Reduce the number of devices connected to the same router.

2. Connection Methods for DWARF II

2.1 Smart Connection

Smart Connection allows you to connect directly from the DWARFLAB app homepage.

Turn on DWARF II and wait 15 seconds.
Open the DWARFLAB app and click Connect.
Ensure the following:
- Your phone/tablet supports Bluetooth 4.0 and WiFi 5GHz/2.4GHz.
- VPN is turned off.
- Bluetooth, WiFi, and GPS/location permissions are enabled on your phone/tablet.

2.2 WLAN Connection

Follow the Smart Connection steps above.
Go to Settings > Connection Settings > Activate WiFi at Startup and turn it on.
Reconnect DWARF II from the app homepage by clicking Connect.
Next time, you can directly connect to DWARF II’s WiFi from your phone/tablet’s WLAN list.

Note: If using a tablet without GPS or Bluetooth, follow these steps:

Connect DWARF II to a device with GPS/Bluetooth and enable Activate WiFi at Startup.
Reconnect DWARF II from the tablet’s WLAN list.

2.3 STA Connection

Complete the Smart Connection steps.
Go to Settings > Connection Settings > STA and turn it on.
Return to the app homepage and connect.
Once connected, DWARF II will automatically enter STA mode when within WiFi range.

By following these steps, you should be able to resolve most connection issues with DWARF II. If problems persist, feel free to contact our support team at support@dwarflab.com for assistance.

Hi, how can I help you?

DWARF 2 Trouble Shooting

Article

Battery Maintenance and FAQs

DWARF 2 Telescope FAQ Hub

How to Deal With Album Display/Download Anomaly

How to Deal With Calibration Failure

How to Deal With Connection Problems for DWARF II

How to Deal With Motor Reset/Position Failed

What If My Astro Photos Stop Stacking